20130115_SVN138d->SVN145a
1. Enable Cache Read feature for IM-flash
2. Support 256GB for IM-flash
3. Fix FDMA not done hangup issue when ECC fail at ncq last access LBA
4. Fix free block number inconsistance when ECC fail at Security Erase.
5. Speed up initial timeing when wakeup from DEVSLP
6. Fix ISP mode in DEVSLP HW, set GPIO12 as open-drain.
7. Fix initialize ssd erase count value issue.
----------------------------------------------------------------------------------------
20130117_SVN145a->SVN146a
1.fix can't read thermal sensor valur issue by utility.
2.This package include TSB and Sandisk 256G:
TH58TEG7DDJTA20_19c_4CH/8CE_TX1H
TH58TEG8DDJTA20_19c_4CH/4CE_TX3G
SDTNQGBMB016GP_19c_4CH/8CE_TT1H
the MPTOOL JMMPTOOL.INI must set "ResPercentage=108" 优盘之家
----------------------------------------------------------------------------------------
20130306_SVN146a->SVN155kw
1. Fix some corner ecc halt FDMA issues;
2. Fix a security erase bug;
3. Fix some SMART attribute content.
4. Enhance the error handling of nand drive
5. Fix a DevSlp flow bug.
7. Optimization I/M L84A Flash.
8.This package include TSB and Sandisk 256G:
TH58TEG7DDJTA20_19c_4CH/8CE_TX1H
TH58TEG8DDJTA20_19c_4CH/4CE_TX3G
SDTNQGBMB016GP_19c_4CH/8CE_TT1H
the MPTOOL JMMPTOOL.INI must set "ResPercentage=108"
----------------------------------------------------------------------------------------
20130403_SVN155kw->SVN167d
1. Enhance L84A NAND error handling.
2. Enhance SATA DEVSLP feature.
3. Integrate TSB19nm TypeC 256GB into standard f/w without over provision.
4.Upgrading F/W from svn155kw to svn167d, must check the "Preformat" option in MPTool.
----------------------------------------------------------------------------------------
20130430_SVN167d->SVN171b
1. Add Intel L84A advanced shift read for higher endurance.
2. Fix some issues of Micron 2 die per 1 ce NAND.
3. Fix the WHCK trim test timeout issue.
4. Fix DRAM test fail by GDP file(02E).
5. Fix Check table file by mp tool(073).
6. Fix SSD have system F/W, Auto detect 2 times issue by mp tool(073).
7. "Test bin" folder only for test use, JM not real verification.
----------------------------------------------------------------------------------------
20130717_SVN171b->SVN198
1. Support L85A Flash at mp tool L85A version.
2. Drive current setting:( just for reference)
{IM-L85 NAND} 256G:16mA, 128G:14mA, 64G:12mA
{SanDisk NAND} 256G:10mA, other: 8mA
{SanDisk NAND JM board} 256G: 12mA, other 8mA U盘之家
3. Add Intel L84A advanced shift read for higher endurance.
4. Fix some issues of Micron 2 die per 1 ce NAND.
5. Fix the WHCK trim test timeout issue.
6. Fix DRAM test fail by GDP file(4/9).
7. Fix Check table file by mp tool(071).
8. 128GB mSATA 1CE2Die partial program.
9. Shorten Shift read delay.
10. Modify Flash error handling for MD5 check issue.(data retention)
11. Add uart_cmd_channel for limiting the dump range and adding a "RWCNT" command to show host R/W info.
12. Flash.ini modify_130822.
----------------------------------------------------------------------------------------
20131002_SVN198->SVN252
1. This version can't support L85A Flash.
2. Add F/W devslp function on-off switch by ini file.(def.=0, enable=1)
3. Follow JM SMART table to arrange SMART attributes.
4. Enhance 128GB, 256GB Random Write performance.
5. Pass WHCK8.1 verification.
6. Improve reliability for abnormal power cycle test. www.upan.cc
7. Check PCB DEVSLP pin status while Host issues set feature for Device Sleep function but PCB not ready.
8. Improve Code Block protection and reliability.
9. Option items note (base on PCB and Flash):
If burn in or temperature test have some ECC error, please try to setting below value:
a.Drive current setting by mp tool. (this is controller to Flash current)
b.Drive current setting by mptool.ini file. (this is Flash to controller)
----------------------------------------------------------------------------------------
20131015_SVN252->SVN263
1. Improve L84A 64G(2CE),128GB(4CE) sequential Read performance.
2. Fix erase count abnormal under continue abnormal power cycling test.
JMF667和667H开卡工具A.2.03.096:http://www.upan.cc/tools/mass/JMicron/3178.html